Xometry.pro
en – EU
Knowledge & Community
Search
K
Quote & source your parts
Europe Europe
English DeutschFrançaisItaliano
Türkiye Türkiye
United Kingdom United Kingdom
Global Global
select
navigate
switch tabs
Esc close

Get Instant Quote

Use our Instant Quoting Engine to easily quote and source your parts online

Get a Quote
Back
 Profile
Menu
Materials Library
Manufacturing Stories & Cases
Articles
E-Books & Guides
Free Tools
Webinars
Free Courses
Community Discussions
Create Topic
Quote & Source Your Parts
Get a Quote

Edit topic

Home Xometry Community Manufacturing Shrink-fitting a thin stainless sleeve into a thick steel housing

Shrink-fitting a thin stainless sleeve into a thick steel housing

H
6

Hi! I’m working on a shrink-fit joint where a thin-walled 304 stainless sleeve is installed into a bored pocket in a much larger 4140 steel housing. The sleeve carries only light axial loads, but I want to size the interference so the hoop stress doesn’t crush or ovalise it. Most interference-fit guidance assumes shaft-and-hub geometry, which doesn’t translate well to a thin liner. How do you estimate hoop stress for a thin sleeve-in-bore to pick a safe fit?

Link copied
1
    • H

      Hi! I’m working on a shrink-fit joint where a thin-walled 304 stainless sleeve is installed into a bored pocket in a much larger 4140 steel housing. The sleeve carries only light axial loads, but I want to size the interference so the hoop stress doesn’t crush or ovalise it. Most interference-fit guidance assumes shaft-and-hub geometry, which doesn’t translate well to a thin liner. How do you estimate hoop stress for a thin sleeve-in-bore to pick a safe fit?

      Reply
    • N

      Hoop stress is a lot more sensitive than in thick hub cases. A simple approach is to treat the sleeve as a thin-walled cylinder and the housing as rigid, then use the basic Lame’s equations for hoop stress:

      σθ = pr/t

      p = radial interference pressure, r = sleeve mean radius, t = sleeve wall thickness.

      The interference sets p via: p = (δi/r) x (Es/(1−𝝂s2p); with δi = radial interference, Es​ – stainless steel bulk modulus, 𝝂s​ = stainless Poisson’s ratio.

      Axial stress is usually negligible for light loading, unless you have long, thin sleeves with end constraints. The key is that thin wall = high stress for small interference. Keep hoop stress < ~0.4–0.5·σ_y of 304 stainless (about 205 MPa yield) to avoid permanent ovalisation.

      Reply
      Link copied
      1
Shrink-fitting a thin stainless sleeve into a thick steel housing
Your information:




Suggested Topics

Topic
Replies
Views
Activity
Depozit
Manufacturing
0
45
Feb 07
Laser cutting pc panels for machine safety enclosures
Manufacturing
Hi, I’m producing clear polycarbonate panels for a machine safety enclosure, cut from 4 mm sheet with small mounting holes and tight internal radii. Optical clarity and edge integrity matter more than cosmetics. From... read more
L
R
1
87
Feb 04
Printing a 3D Model Purchased from a Third Party
Manufacturing
Hello, I was wondering if there would be any issues in requesting the production of a print from a model purchased from a third party.Thank you and keep up the good work! read more
s
4
227
Jan 23
Manufacturing Wheels for Fingerboards
Manufacturing
Hello,I am writing because I am developing fingerboard wheels as a new product within my own brand. I professionally manufacture fingerboard decks and concrete obstacles, and now I am expanding my catalogue with cast... read more
j
2
303
Jan 20
X-ring performance on a curved face seal in a poppet valve
Manufacturing
I’m reverse-engineering a small hydraulic shutoff valve used in an industrial test stand, and I’m trying to understand whether the face-sealing setup for the poppet is causing a recurring internal leak. The poppet uses... read more
L
M
1
462
Dec 22

Edit topic