Xometry.pro
en – EU
Knowledge & Community
Search
K
Quote & source your parts
Europe Europe
English DeutschFrançaisItalianoEspañol
Türkiye Türkiye
English Türkçe
United Kingdom United Kingdom
English
Global Global
English
select
navigate
switch tabs
Esc close

Get Instant Quote

Use our Instant Quoting Engine to easily quote and source your parts online

Get a Quote
Back
 Profile
Menu
Materials Library
Manufacturing Stories & Cases
Articles
E-Books & Guides
Free Tools
Webinars
Free Courses
Community Discussions
Create Topic
Quote & Source Your Parts
Get a Quote

Edit topic

Home Xometry Community Industrial Design SLS – Design Tips

SLS - Design Tips

0
L
5

Good evening,

As part of a project for my Mechanical Engineering degree, I am working on the task of “Implementing 3D printed parts in production”. I have already gained some experience with FDM printing, but unfortunately not in the SLS area.
The component I am dealing with should be optimized for printing. Now the component is clamped with two M8 countersunk screws. Unlike metal, plastic can creep under continuous load (especially at increasing temperatures), so the tightening torque of the screw decreases. Is creep to be expected with common SLS powders (e.g. PA12/PA11/iglidur i6)? — So, would one have to insert a metal sleeve for relief?

Thanks in advance!

Automatically translated from: Deutsch
See original
Link copied
Solved by Tilmann98

I think a general recommendation can be to test your SLS parts under the given conditions, as there are many physical factors that can influence these. But all in all, SLS PA12/PA11 under the conditions you specified is a really good alternative to, for example, FDM ABS/Nylon/PLA.

    • L
      Good evening,

      As part of a project for my Mechanical Engineering degree, I am working on the task of “Implementing 3D printed parts in production”. I have already gained some experience with FDM printing, but unfortunately not in the SLS area.
      The component I am dealing with should be optimized for printing. Now the component is clamped with two M8 countersunk screws. Unlike metal, plastic can creep under continuous load (especially at increasing temperatures), so the tightening torque of the screw decreases. Is creep to be expected with common SLS powders (e.g. PA12/PA11/iglidur i6)? — So, would one have to insert a metal sleeve for relief?

      Thanks in advance!

      Automatically translated from: Deutsch

      See original
      0
      Reply
    • T

      How is the component clamped with the M8 countersunk screws? Through the threads, which are inserted into the component?

      0
      Reply
      Link copied

    • What are the approximate operating temperatures? In general, the temperature does not play a major role if it does not exceed, for example, 70 C (PA12). Creep can of course be taken into account, but it depends on the applied load.

      p.s. I found this video from Xometry. It’s not exactly your case, but it helps to get a sense of how different 3D printing technologies and materials (including PA12) behave under comparable conditions.

      0
      Reply
      Link copied
    • L

      All clear, thank you very much. The screws are screwed into a stainless steel plate below – the plastic part is clamped between the screw head and the plate (I would have a screenshot, but unfortunately I can’t insert it)
      The operating temperatures vary between 5° and 60°, although most of the time there is room temperature.

      0
      Reply
      Link copied
      • T
        Luca

        I think a general recommendation can be to test your SLS parts under the given conditions, as there are many physical factors that can influence these. But all in all, SLS PA12/PA11 under the conditions you specified is a really good alternative to, for example, FDM ABS/Nylon/PLA.

        0
        Reply
        Link copied
    • Xometry Engineer

      Hello Luca,

      I can only agree with Tilmann 98 here. SLS parts are generally of high quality and have a density of almost one in PA12, in MJF also above one. The difference is about 10%. Another possibility to minimize creep would be PA12GF (glass filled). This PA12 has a 30% glass content and is harder, but then tends to break more quickly if excessive forces are applied.
      0
      Reply
      Link copied
SLS – Design Tips
Your information:




Suggested Topics

Topic
Replies
Views
Activity
Thermal expansion modelling for a braced rectangular steel tank
Industrial Design
hi, for a welded steel coolant reservoir for a test stand - 4 m × 2 m × 1.5 m with internal bracing I need to account for thermal expansion. Fluid runs at 80–90... read more
B
0
31
Dec 22
Designing holes for M3 threaded inserts in an ABS enclosure
Industrial Design
Hi! In my design for a small ABS enclosure for an onboard sensor module I want to switch from molded bosses to heat-set M3 inserts for the lid screws. Before I finalize CAD, what... read more
A
o
1
116
Dec 23
Airtight joint between two aluminum frame enclosures?
Industrial Design
Hi, I have two 400 mm cubical enclosures from 20×20 mm aluminum profiles with glass on all sides except one. I need to connect them into a single temperature-controlled unit and keep the joint... read more
M
F
1
245
Dec 12
How to correctly specify standard and non-standard threads in a technical drawing?
Industrial Design
For a machined part that has both standard and non-standard thread types, what’s the best way to call out threads in the technical drawing? In particular, should I use thread callouts or full detail... read more
I
R
6
781
Nov 14
Drawing callout for tight tolerance over short bore length
Industrial Design
hi, I have an aluminum housing for a small gearbox where the bearing seats are, of course, critical. I need to hold tight tolerances on the ID and OD, but only over a short... read more
A
S
4
586
Oct 31

Edit topic