Xometry.pro
en – Global
Knowledge & Community
Search
K
Quote & source your parts
Europe Europe
English Deutsch Français Italiano Español
Türkiye Türkiye
English Türkçe
United Kingdom United Kingdom
English
Global Global
English
select
navigate
switch tabs
Esc close

Get Instant Quote

Use our Instant Quoting Engine to easily quote and source your parts online

Get a Quote
Back
 Profile
Menu
Materials Library
Manufacturing Stories & Cases
Articles
E-books & Guides
Free Tools
Webinars
Free Courses
Community Discussions
Create Topic
Quote & Source Your Parts
Get a Quote

Edit topic

Home Xometry Community Industrial Design Tolerance stack up question

Tolerance stack up question

0
F
1

Hi all, I’m new to the world of tolerance stack up and working on a snap-fit assembly with five injection-molded ABS components. In prototypes I’m encountering inconsistent engagement forces, likely due to tolerance accumulation across mating features. How can I use GD&T or tolerance analysis software to identify and control critical variations? Are there any beginner-friendly best practices or tools you’d recommend to ensure consistent performance?

Link copied
Solved by Joao Clemencio

Hi Faizan,

We have an extensive article explaining everything about tolerances and how to use them when creating your part: https://xometry.pro/en-eu/articles/standard-tolerances-manufacturing/

Actually we don't have any tool or software to help you with it, but after reading the article above, you should be able to use the right tolrances on your part.

Good luck!

    • F

      Hi all, I’m new to the world of tolerance stack up and working on a snap-fit assembly with five injection-molded ABS components. In prototypes I’m encountering inconsistent engagement forces, likely due to tolerance accumulation across mating features. How can I use GD&T or tolerance analysis software to identify and control critical variations? Are there any beginner-friendly best practices or tools you’d recommend to ensure consistent performance?

      0
      Reply
    • Xometry Engineer

      Hi Faizan,

      We have an extensive article explaining everything about tolerances and how to use them when creating your part: https://xometry.pro/en-eu/articles/standard-tolerances-manufacturing/

      Actually we don’t have any tool or software to help you with it, but after reading the article above, you should be able to use the right tolrances on your part.

      Good luck!

      0
      Reply
      Link copied
Tolerance stack up question
Your information:




Suggested Topics

Topic
Replies
Views
Activity
Minimum hole diameter vs sheet thickness 316L
Industrial Design
Hello, I would like to produce a stainless steel 316L bracket, 3 mm thick, cut by fiber laser. I need to include several small holes for drainage and fastening, and I’ve heard there might... read more
F
0
12
Jul 23
Ejector pin placement near snap-fit
Industrial Design
I’m working on a small injection-molded housing for an automotive sensor, using PA6 GF30. There are two snap-fit arms inside (cantilever type), about 2 mm-thick walls. I’m not sure where to place the ejector... read more
M
T
5
58
Jul 18
Adding countersinks to formed stainless sheet metal
Industrial Design
Hello, I'm working on a sheet metal enclosure (as in the image) that requires flush mounting for M6 countersunk screws. I need to add a countersink on a few holes, but the part is... read more
D
M
D
2
95
Jul 03
Fastener size choice for a through-hole in 4 mm anodized aluminum plate
Industrial Design
Hi! Designing a lightweight enclosure for a small UAV component, using 4 mm thick anodized aluminum sheets. For the assembly, I need to fasten this plate to a 3D-printed ABS bracket underneath, which acts as... read more
K
e
E
3
213
Jun 30
Cracking at snap-fit hook base in SLS PA12
Industrial Design
Hello everyone, I'm using SLS 3D printing (PA12, 0.12 mm layer height) to create a snap-fit enclosure for a handheld sensor device. The enclosure has three internal hooks that flex about 1.5 mm during... read more
F
A
2
209
Jun 24

Edit topic